rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rs5-r30/rd30 3.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! ? 8 pin sil package ? wide 2:1 input range ? 1600vdc isolaton ? contnuous short circuit protecton ? efciency up to 84% ? operatng temperature range -40 ~ +85c ? plastc case standard , metal case (optonal) ? remote on/of control (optonal) output specification voltage accuracy: 1% maximum output current: see table line regulaton: 0.5% max. load regulation: from 25% to 100% loading 1% max cross regulaton (dual output): 5% short circuit protecton : indefnite (automatc recovery ) ripple noise (20mhz bandwidth): 75mv pk-pk max. temperature coefcient: 0.02% c capacitor load: see table transient recovery time: 300us, typ. transient response: ( deviaton) 3% max. input specifications voltage range: see table start up time: 20ms, typ. max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 35ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1600vdc i/o isolaton capacitance: 680pf max. i/o isolaton resistance: 1000m ohm, min switching frequency: 100 - 650khz humidity: 95% rel h reliability calculated mtbf : > 1.34mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec en 60950-1 remote on controll: on: open or high impedance remote of controll: of: 3-6ma input current (via 1k) of stand by current (nominal vin): 3ma max. environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: pin material: non conductve black plastc pin material sip case: c519r-h solder -coated potng material: epoxy (ul94v-0 rated) weight case- sip: 4.8g, typ. dimmension sip: 0.86 x 0.36 x 0.44 absolute maximum ratings (1) input surge voltage (100ms)/ max. 5 v models: 15vdc max. 12v models: 36vdc max. 24v models: 50vdc max. 48v models: 100vdc max. soldering temperature: 260c max. (2) emc specifications radiated-/conducted emissions: en55022 class a (see emi filter note) esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 model selection guide model number input voltage range (vdc) input current output voltage (vdc) output current efficiency @fl(%) capacitor load(uf) no - load (ma) full load (ma) m i n . l o a d (ma) full load (ma) rs5 - 05 03r30a1 4.5 - 9 65 640 3.3 175 700 74 2200 rs5 - 0505 r30a1 4.5 - 9 70 800 5 150 600 76 2200 rs5 - 0512 r30a1 4.5 - 9 75 750 12 62. 5 250 82 470 rs5 - 0515 r30a1 4.5 - 9 75 750 15 50 200 82 470 rs5 - 12 03r30a1 9 - 18 25 260 3.3 175 700 76 2200 rs5 - 1205 r30a1 9 - 18 15 320 5 150 600 81 2200 rs5 - 1212 r30a1 9 - 18 35 305 12 62. 5 250 84 470 rs5 - 1215 r30a1 9 - 18 35 305 15 50 200 84 220 rs5 - 24 03r30a1 18 - 36 15 133 3.3 175 700 74 2200 rs5 - 2405 r30a1 18 - 36 15 160 5 150 600 79 2200 rs5 - 2412 r30a1 18 - 36 20 156 12 62. 5 250 82 470 rs5 - 2415 r30a1 18 - 36 20 152 15 50 200 84 470 rs5 - 48 03r30a1 36 - 72 10 66 3.3 175 700 75 2200 rs5 - 4805 r30a1 36 - 72 10 82 5 150 600 78 2200 rs5 - 4812 r30a1 36 - 72 15 78 12 62. 5 250 81 470 rs5 - 4815 r30a1 36 - 72 15 78 15 50 200 81 220 rs5 - 0505 rd30a1 4.5 - 9 90 800 5 75 300 77 470 rs5 - 0512 rd30a1 4.5 - 9 90 760 12 31. 25 125 81 220 rs5 - 0515 rd30a1 4.5 - 9 90 750 15 25 100 82 100 rs5 - 1205 rd30a1 9 - 18 45 320 5 75 300 80 470 rs5 - 1212 rd30a1 9 - 18 45 308 12 31. 25 125 83 220 rs5 - 1215 rd30a1 9 - 18 45 312 15 25 100 82 100 rs5 - 2405 rd30a1 18 - 36 20 160 5 75 300 80 470 rs5 - 2412 rd30a1 18 - 36 20 154 12 31. 25 125 83 220 rs5 - 2415 rd30a1 18 - 36 20 154 15 25 100 83 100 rs5 - 4805 rd30a1 36 - 72 15 82 5 75 300 78 470 rs5 - 4812 rd30a1 36 - 72 20 80 12 31. 25 125 80 220 rs5 - 4815 rd30a1 36 - 72 15 78 15 25 100 81 100 suffix ?c? means with control pin suffix ?m? means with metal case the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg - electronic.de dc/dc-converter -/d ete ne d tt we energize electronics! an acal group company we energize electronics! r s 5 - xx xx x x 30 power (w) input t ype a x * x code inter nal isolation (kvdc)
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20mhz. +vout +vout +vin lin current probe cin dc/dc converter load dc/dc converter scope load - vin - vout - vout emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. + v o u t + v in l d c / d c c o n v e r t e r l o a d c 1 - v in - v o u t c 1 l v - 0 5 2 2 0 u f / 2 5 v 5 . 6 u h v - 1 2 s 1 0 0 u f / 1 0 0 v 1 8 u h d u 1 2 1 0 , 2 .2 u f / 1 0 0 v v - 2 4 1 2 1 0 , 1 0 u f / 3 5 v 1 8 u h v - 4 8 1 0 0 u f /1 0 0 v 5 6 u h u . u u, u - - . cvrr 3 1. u , . 2. 25 100 , 100 , uu 5. 3. u 20h . 4. v . 5. v 100 - 25 ,25 . 6. u u u u u u 12uh u c4uf, sr1.0 100h . . r / ff 3.06.0a u u 1 8. x u u u u . uu . . 25 u . 10. u u u a, f u u. 11. a x u u c61000 - 4 - 4 c61000 - 4 - 5. rs u - - , 220uf/100v. v 1 36 a - v c1 l rs5 - 05xxr30/rd30a1 220uf/25v 5.6uh rs5 - 12xxr30a1 100uf/100v 18uh rs5 - 12xxrd30a1 1210, 2.2uf/100v 18uh rs5 - 24xxr30/rd30a1 1210, 10uf/35v 18uh rs5 - 48xxr30/rd30a1 100uf/100v 56uh dc/dc-converter rs5-r30/rd30 3.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20mhz. +vout +vout +vin lin current probe cin dc/dc converter load dc/dc converter scope load - vin - vout - vout emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. + v o u t + v in l d c / d c c o n v e r t e r l o a d c 1 - v in - v o u t c 1 l v - 0 5 2 2 0 u f / 2 5 v 5 . 6 u h v - 1 2 s 1 0 0 u f / 1 0 0 v 1 8 u h d u 1 2 1 0 , 2 .2 u f / 1 0 0 v v - 2 4 1 2 1 0 , 1 0 u f / 3 5 v 1 8 u h v - 4 8 1 0 0 u f /1 0 0 v 5 6 u h u . u u, u - - . cvrr 3 1. u , . 2. 25 100 , 100 , uu 5. 3. u 20h . 4. v . 5. v 100 - 25 ,25 . 6. u u u u u u 12uh u c4uf, sr1.0 100h . . r / ff 3.06.0a u u 1 8. x u u u u . uu . . 25 u . 10. u u u a, f u u. 11. a x u u c61000 - 4 - 4 c61000 - 4 - 5. rs u - - , 220uf/100v. v 1 36 a - v c1 l rs5 - 05xxr30/rd30a1 220uf/25v 5.6uh rs5 - 12xxr30a1 100uf/100v 18uh rs5 - 12xxrd30a1 1210, 2.2uf/100v 18uh rs5 - 24xxr30/rd30a1 1210, 10uf/35v 18uh rs5 - 48xxr30/rd30a1 100uf/100v 56uh
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 rs5-xxxxr30a1 rs5-xxxxr30a1m rs5-xxxxr30a1 rs5-xxxxr30a1m rs5-xxxxr30a1 rs5-xxxxr30a1m dc/dc-converter rs5-r30/rd30 3.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! mechanical specifications the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
